24h selector desk: +1-800-555-0198 | [email protected] Regions: North America / Europe / Asia Pacific | EN / DE / ES / ZH
2026-11-13

Mechanical Power Transmission Ordering Checklist: 7 Things We Check Before Sending a PO

Who this checklist is for

You order sprockets, gears, bearings, and the occasional VFD for maintenance, repair, or a new install. You don't want to find out at 2 a.m. that the part doesn't fit—or that a $60 sprocket has halted a production line for three days. You want something you can print and actually check off before the PO goes out. Here are our 7 steps.

I've handled MRO power transmission orders for 11 years—sprockets, gears, bearings, the occasional actuator. I've made and documented 9 significant mistakes totaling roughly $12,000 in wasted budget. Every single one of them was painful, avoidable, and traced back to skipping a check that took less than ten minutes. Now I keep the team's checklist. This is it.

1. Lock in the standard, not just the product name

"40-tooth sprocket" means nothing until you specify: ANSI vs. metric, pitch, number of teeth, bore, keyway width, and keyway depth. "40 teeth" could refer to an ANSI 40-pitch chain (½ inch), a metric 40-pitch (which is actually 12.7 mm—close to ANSI but with different tolerances), or something else entirely. The Martin Sprocket & Gear catalog is one of the more comprehensive references out there, but it can't tell you which of those three you actually ordered.

Back in 2019 I ordered a replacement sprocket that looked correct in the PDF. It wouldn't fit the shaft. Not "obviously wrong." It almost fit. I'd misread the hub dimensions—thought I was looking at a ½-inch bore when the actual spec called for ⅝. The cost of that mistake, between the returns and the line downtime, was hundreds of times more than the $80 we "saved" by not asking.

What to do: Grab calipers and measure the part coming off the machine. Don't trust the annotation on the page you're reading. Your measurement is the only number that matters.

2. Deep groove ball bearings vs. cylindrical roller bearings aren't interchangeable

A deep groove ball bearing handles radial and axial loads, works well at high speed, and is cheap. A cylindrical roller bearing handles much higher pure radial loads but has almost no axial capability. Getting the direction and magnitude of thrust wrong is an easy way to eat a bearing in six weeks.

My worst example: I replaced a deep groove ball bearing on a belt-driven shaft under radial load. Six weeks later it failed. Not a defect—wrong load. The balls had brinelled under radial stress that a cylindrical roller bearing would've handled without complaint.

What to do: Pull the actual load specs. If you're picking between "high speed" and "heavy load" by vibe, stop and hand the part number and specs to an application engineer. Yours or the supplier's. Their time is cheaper than your downtime.

3. VFDs—check whether the motor is actually inverter-duty rated

VFD stands for Variable Frequency Drive. You don't need the internal wiring theory, but you do need to know what it's connected to. A standard NEMA MG 1 Part 30, non-inverter-duty motor on a PWM drive will have its life shortened meaningfully—bearing current or insulation degradation, over time. NEMA MG 1 Part 31 is the inverter-duty spec. That's the one you need to verify before purchase, not after.

The "VFDs will ruin standard motors" line was true back in the early 2000s, when most drives output a 6-step waveform and common-mode voltage spikes were common. Today, modern PWM drives and inverter-duty motors have mostly turned a real problem into a manageable one—but only if you buy the right motor. One of my early POs was a general-purpose motor plus drive, chosen to save money. Fourteen months later the motor shorted and every dollar we'd saved became a cost.

What to do: Put the drive model number and the motor nameplate side by side. Confirm the Part 30 vs. Part 31 distinction. If that sounds like homework, that's exactly why it gets skipped—and why it shows up in so many failure reports.

4. Catalog dimensions ≠ fit dimensions

The Martin Sprocket & Gear catalog is thorough on specs. What it rarely shows—because it can't—is the exact keyway depth, hub length, or dimensional tolerance your specific machine needs. If you're buying off a thumbnail, you'll find out the hard way.

What to do: Before the PO goes out, pull the actual drawing or CAD file. Look at the bore and keyway, specifically. Ask the supplier to confirm with a physical drawing. "Per catalog" is only a legitimate answer after every dimension has been checked in pre-purchase.

5. Lead time and warehouse location are the real cost, not the price tag

A part that's 20% cheaper but shows up a week late isn't cheaper. That lesson cost us four figures: a $60 sprocket ordered from a "catalog" supplier whose local warehouse didn't actually stock it. The part arrived 9 days late. Production stopped for 3 of them.

What to do: Before you order, check stock in the supplier's actual inventory or warehouse locator—not just "available in catalog." Confirm which ship-from location they're using. If you're relying on "next-day," verify that means next-day to you, not next-day to their receiving dock.

6. A "one-stop shop" usually means "most things," not "our strongest thing"

If you ask a vendor "can you supply sprockets, bearings, VFDs, linear actuators, and motors?" they'll all say yes. That doesn't mean they're strong across every category. The vendor who tells you honestly "this isn't our strength—here's who does it better" has earned my trust on everything else. If you ask me, that's worth more than a blanket yes.

I'd rather work with a specialist who knows their limits than a generalist who overpromises. That's not to say a single company can't do multiple categories well—it's just rare that every category gets the same depth of stock, pricing, and technical support.

What to do: Ask the supplier directly what they're strongest at—then ask what they'd recommend buying elsewhere. The second answer tells you more about whether you should send them your whole basket.

7. Inspect on arrival, before it hits the shelf

I don't have hard data on industry-wide wrong-part return rates, but based on our own five-year records, my sense is that roughly a third of RMA cases could've been caught at the receiving dock. Check the part number, the quantity, and—yes—caliper five key dimensions: bore, keyway, pitch/number of teeth, outside diameter, and width.

What to do: Build a quick arrival checklist for each shipment and tape it to the receiving bench. Don't trust your memory at 4 p.m. on a Friday.

What goes wrong most often

If I had to pick one item to check before any PO goes out, it'd be this: verify the bore and keyway dimensions against the actual drawing before you send it, not after the part arrives. Everything else matters, but that one check is what turns a three-day shutdown into a ten-minute caliper measurement.

And don't treat "order from us for everything" as the default just because it's convenient. Being specific about where one supplier's strength stops and another's starts is what keeps you from finding out the hard way—again.

Lucas Moreau

Lucas Moreau

Lucas Moreau is an independent hydraulic drive systems analyst covering pumps, motors, valves, cylinders, manifolds, and hydrostatic transmission circuits. He applies ISO 4413 safety principles and evaluates pressure, flow, displacement, volumetric efficiency, pressure drop, fluid cleanliness, thermal balance, and actuator speed across operating states. His application guides help equipment engineers compare circuit architectures, size components, manage energy losses, and define safe commissioning and maintenance checks.